Are You almost done setting up your new apartment and now stressing over the kitchen’s outlook?
You want it to look modern so that it goes well with the overall theme of the apartment. Your friend just suggested you use LED lighting for the cabinets, but you don’t know how to install undercabinet LED lighting.
Under Cabinet, LED lighting surely does look good and adds up to the visual aesthetics of your kitchen. Not only are they cheap but also they provide amazing lighting for your kitchen.
How to Install Under Cabinet LED Lighting?
Keep on reading as we guide you through the steps of installing under cabinet led light efficiently. The steps are super-easy, and you can do it all by yourself.
Step-1: Plan Out Everything
The very first task for you to set up an LED under your cabinet is to form up a plan. A proper plan will keep your tasks coordinated and will help to sequentially carry out each task. Take a pen and paper and start illustrating the infrastructure of the LED system.
This plan should include the placement of each equipment, such as the switch, terminal, power supply, etc. Also, you need to form up an efficient way for your wire so that it looks minimalistic inside the cabinet.
This is important because tangled wire not only looks bad but also creates room for receiving damage over time.
Step-2: Place Power Supply
For your LED to light up, you need a proper power supply under your cabinet. Installing a wiring box sounds like a smart move because all you need to do now is put the wiring in place.
The next step includes opening up the box, making a hole in the cabinet, and shove the wiring up the wiring box and out of the hole.
Keep in mind, using the wiring box in a hidden manner makes it look minimalistic. Also, to supply power to the LED, try to use a hidden and accessible outlet.
Step 3: Work on the Wiring
In this step, you will need pliers to strip the insulation of the wire. Use fishing tape to hook to the ground, and for covering the connection — use electrical tape.
Next, pull the fish tape until you see the wire exposing about 10 inches. You won’t be needing the fish tape anymore afterward.
Using a utility knife, free out the individual three wires inside the sheathing. Now strip the ends of the pigtails, grab all three of the wires and connect them to existing and new outlets and keep one for the pigtail. Lastly, use a wire nut to join them.
Do the same for the ground and black wires. After you are done, put all the wires inside the box, screw it, and put it back again.
Step 4: Add a Dimmer
To install a dimmer, Cut the wire and put it through the wiring box on the opening of the outlet. Place the dimmer in the wall and wire them on the new outlet.
Next, take the outlet and place it properly to make the trim plate secure. In the inputs of the wireless dimmer, put the red and black wires of the power supply.
Now, tighten the setscrew to complete the process.
Step 5: Making the Power Supply Functional
Take both the power supply and dimmer, and place them on the upper cabinets. Not inside but on top of it so that it is not visible. Now plug it in the and supply power to the new outlet through the power supply.
You will need solid-core wiring that is available as thermostat wiring. The size of the wire should be 18/2, enough to reach underneath from the very top of the cabinet. Next, drape it along the side of the cabinet.
Step-6: Working on the Terminal
For it to reach the underneath of the cabinet, cut the red and black wire. Take the red wire and add it to the terminal’s end and tighten the screw. The same process should be repeated for the black wire. Now add wiring, maintaining a branch-like pattern in two directions, and cover the walls of the cabinet.
Step-7: Cut the LED Tape
First of all, measure the length of the cabinet that needs to be covered with the LED tape. Depending on that, cut the LED tape with scissors. The process should be repeated for all the cabinet walls.
Step-8: Wiring the LEDs
Using the tape-light extension of the LED, you can simply turn the power terminal into a splitter. Doing so will enable you to send power in both of the walls. The extension usually has two wires, one for positive and one for negative.
Your next task is to join them to the extension by simply peeling away the backing under the LED strip. Be sure to maintain the alignment of the extension and the tape’s markings. Make sure the tape is properly set by wiggling it.
Snap the lock by flipping the connector cover with a screwdriver. Using a slotted screwdriver will do the trick.
Repeat the process with other strips on the other walls of the cabinet as well. After you are done with it, take all of the positive ends, twist it, and fit them to the terminal. In the same way, add the negative ends and tighten the screw.
Step-9: Create a Passageway for the Wires
Now that you have set the LED in place and done with the wiring, next create a passageway for the wiring by drilling holes into the cabinet. You can then pull wires through these holes and manage them in such a way so that they are not visible to the naked eye.
Finally, everything is set, and you can now add a switch to help you to turn the lights on and off. Installing the switch under the cabinet sounds like a good place. Wireless switches are available that helps to regulate the LEDs.
Simply screw the wireless pad in the wall, disconnect and reconnect the power, it will pair with the dimmer. Lastly, take the terminal and screw it under the cabinet.
Installing an under-cabinet LED lighting is super-easy, you see. Even though the process looks a little bit complex at first, it is quite simple if you know what you are doing. Now that you know how to install under cabinet LED lighting, you will find the process quite effortless.